Enerco HS35LP Manuel d'utilisateur télécharger pdf (Page 4)

The connection of Model 35LP to an LP-Gas cylinder must be

made in a well ventilated area using the regulator and hose

assembly supplied with the appliance. DO NOT attempt to adjust

this regulator. It has been preset at the factory to provide safe

and proper operation of the appliance. Use a 7/8” open end

wrench to connect the POL fitting (supplied with the LP

regulator) to the LP-Gas cylinder. Turn the POL nut in a counter-

clockwise direction (left hand thread) until tight. DO NOT use

pipe compound on POL threads.

The heater must be located at least six feet away from any LP-

Gas cylinder and must not be directed toward any LP-Gas

cylinder within 20 feet. If more than one heater is used, they and

the supply cylinders must be separated by at least 20 feet.

The gas supply must be turned off at the LP-Gas supply cylinder

when the heater is not in use.

When the heater is to be stored indoors, the connection

between the LP-Gas supply cylinder and the heater must be

disconnected and the cylinder removed from the heater and

stored in accordance with Chapter 5 of the Standard for the

Storage and Handling of Liquefied Petroleum Gases, ANSI/NF-PA

58 (U.S.), OR CAN/CGA B149.2 (Canada).

If connected to a permanently installed LP Gas supply system,

the system requires the use of a two-stage gas regulator

assembly which is normally provided by your LP-Gas dealer as

part of the LP-Gas supply system. Consult with your local LP-Gas

dealer for details concerning proper equipment and installation.

Piping must be clean and free from scale or burr.

Before attempting to ignite the appliance, all gas fittings and

connections must be thoroughly checked for gas leaks. Apply a

small amount of a mild soap and water solution to all fittings

and connections and observe for escaping bubbles. If any leaks

are detected, shut off the gas supply to the appliance

immediately. Wait a minimum of five minutes, repair the leak(s)

and retest for leakage. Dry all fittings and connections after leak

testing.

WARNING

NEVER USE A FLAME FOR GAS LEAK TESTING.

OPERATING INSTRUCTIONS

WARNING:

IF YOU DO NOT FOLLOW

THESE INSTRUCTION EXACTLY, A FIRE

OREXPLOSION MAY RESULT CAUSING

PROPERTY DAMAGE, PERSONAL INJURY,

OR LOSS OF LIFE.

CAUTION

THIS APPLIANCE IS HOT DURING

NORMAL OPERATION. AVOID

PHYSICAL CONTACT.

CAUTION

DO NOT PLACE CLOTHING OR

OTHER COMBUSTIBLE MATERIALS

ON THIS APPLIANCE.

DO NOT operate this heater if any part has been under

water. Call a qualified service technician to inspect the

appliance and to replace any part of the control system or gas

control valve which has been under water.

This appliance must be installed and operated only in locations

where the potential for physical damage to the appliance is

reduced to a minimum. The owner/operator of this appliance

must ensure that precautions are taken to protect the appliance

from physical damage.

LIGHTING AND SHUT-DOWN

Lighting the Heater:

1. Before attempting to light the heater, smell all around

the heater area for gas. Be sure to smell next to the

floor because LP-Gas is heavier than air and will settle

on the floor. Turn on the gas supply to the appliance

and check all fittings and connections for gas leaks

using a mild soap and water solution. NEVER use a

match to check for gas leaks. Should a gas leak occur,

shut off the gas supply to the appliance immediately.

Wait a minimum of five minutes before repairing the

leak.

2. Use only the fuel intended for this appliance. Check the

appliance rating plate for the correct fuel information.

3. Turn off the main gas supply to the appliance. Wait five

minutes.

4. Turn on the main gas supply.

5a. Depress and turn Control Knob counterclockwise to

“Pilot” position and hold for 1-2 minutes. This may take

longer to purge air from the supply hose depending on

the length of the hose being used.

Depress red spark ignition button to light pilot flame

(repeat until pilot lights) and continue to hold Control

Knob at “Pilot” positionfor 30-60 seconds to enable

Pilot Light Safety System.

Fully turn Control Knob to “Hi” position to light burner. or...

5b. With a lighted match held to the burner face, depress

and hold the reset button. After the burner ignites,

hold the reset button depressed for about one minute

or until the burner stays lit when the reset button is

released. DO NOT light the gas at the burner

orifice. DO NOT face heater when attempting to

light. Always stand to the side of the unit when

lighting.

NOTE: In cases where long runs of gas supply lines have been

installed ahead of the appliance, it may be necessary to bleed

trapped air out of the supply lines before lighting the burner.

New installations generally require bleeding of supply lines. Wait

a minimum of five minutes after bleeding the supply lines before

attempting to light the heater.

6. IMPORTANT: DO NOT attempt to adjust the main

burner input using the main gas supply valve, for this

may cause the thermocouple to shut down the burner.

Operating Instructions and Owner’s ManualEnerco Group, Inc. | Gas-Fired Infra-Red Portable Construction Heater

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Enerco HS35LP Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Radiateurs Enerco HS35LP