Enerco HS35LP Manuel d'utilisateur télécharger pdf (Page 3)

The minimum ambient temperature rating for this heater is 20

degrees F.

This heater incorporates a “Tip Over” switch which automatically

shuts off the burner in the event of tipping. Ensure that this

switch is in the vertical position and is secured with the screws

provided (see Fig. 4). DO NOT operate this heater with the

LP-gas supply cylinder in any other than the upright

position.

LOCATION

Although this heater incorporates a “tip over” switch, the heater

and LP-Gas supply cylinder must be located on a hard, flat, level

surface to minimize the risk of accidental tipping. The LP Gas

supply cylinder should be adequately restrained to prevent

accidental tipping. DO NOT OPERATE this heater with the

supply cylinder in any other than the upright position.

This appliance must be installed only in locations where the

potential for physical damage to the appliance (i.e., due to

physical contact) is reduced to a minimum.

The installer must inform the owner/operator of this appliance

that precautions must be taken to protect the appliance from

physical damage.

This appliance produces radiant heat. Therefore, it must be

located at least six feet away from any LP-Gas container and

must not be directed toward any LP-Gas container within 20 feet.

The heater must be installed in a location such that it will not be

exposed directly to water spray, rain, and/or dripping water.

Use of this heater in a draft/windy area may decrease its

efficiency. If possible, operate the unit in a draft free area or

turn the face of the heater away from the draft.

PIPING:

For Model 35LP

(for use with LP-Gas)

This model may be connected to a self-contained LP-Gas supply

system using the hose and regulator assembly supplied with the

appliance, OR, it may be connected to a permanently installed

LP-Gas supply system.

If connected to a self-contained LP-Gas supply system, the hose

assembly must be inspected prior to each use of the heater. If it

is evident that there is excessive abrasion or wear, or the hose is

cut, it must be replaced prior to the heater being put into

operation.

If connected to a self-contained LP-Gas supply system, the

cylinder must have no less than a minimum capacity of 20

pounds and no more than a maximum capacity of 100 pounds of

LP-Gas. DO NOT connect this appliance to a cylinder having less

than a nominal 20 pound capacity of LP-Gas. DO NOT connect

this appliance to more than one (1) 100 pound cylinder.

WARNING

NEVER USE A FORK LIFT TRUCK TYPE

CYLINDER.

GENERAL INFORMATION

A. Your Enerco Technical Products portable gas-fired infra-red

heater comes fully assembled and is tested at the factory for

proper gas and input as stated on the nameplate.

B. Each heater is equipped with a 100% safety shutoff, push

button valve which will automatically stop the flow of gas in

the event the heater fails to operate for any reason. A tip

over switch and an excess flow check are also standard on

the model 35LP.

C. Before proceeding with this installation, be sure to inspect

for damages. The freight company must be notified of any

damages and request that an inspection be made. Enerco

Technical Products will send replacements for damaged

parts only after receiving a signed inspection report to

prove the liability of the freight company.

FOR SAFE OPERATION

A. READ THESE INSTRUCTIONS CAREFULLY. Read and

adhere to these instructions. DO NOT allow anyone

who has not read these instructions to assemble, light,

adjust or operate this heater.

B. LP-Gas IS HIGHLY FLAMMABLE. In the event of a leak, LP-

Gas will accumulate and the possibility of a fire is present.

LP-Gas is scented and its strong odor is readily detectable.

Never strike a match, bring any flame or create an electric

spark in an enclosure when you smell LP-Gas. Ventilate the

area thoroughly, move the heater outside, and correct the

source of the leak before attempting to light any appliance.

C. Always operate the heater with the LP-Gas cylinder in an

upright position on a level non-combustible surface. NEVER

PLACE THE CYLINDER ON ITS SIDE WHEN OPERATING

THE HEATER.

D. DO NOT attempt to operate the heater with any gas

other than that indicated on the heater nameplate.

INSTALLATION INSTRUCTIONS

GENERAL

For the U.S. and/or Canada, the installation of this appliance

must comply with local and/or Provincial codes or, in the

absence of these codes,

• With the (U.S.) National Fuel Gas Code, ANSI Z223.1 –

Latest Edition, AND with the (U.S.) Standard for the Storage

and Handling of Liquified Petroleum Gases, ANSI/NFPA 58,

• With the current (Canadian) CAN/CGA B149.1 AND B149.2

INSTALLATION CODES.

This heater (including hose and regulator assembly) must be

inspected before each use and at least annually by a qualified

service person. If the hose for Model 35LP shows evidence of

excessive abrasion or wear, or if the hose is cut, it must be

replaced prior to the heater being put into operation. The

replacement hose assembly shall be that specified by the

manufacturer. See the parts list.

Operating Instructions and Owner’s ManualEnerco Group, Inc. | Gas-Fired Infra-Red Portable Construction Heater

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Enerco HS35LP Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Radiateurs Enerco HS35LP